 |
Schluter SCHIENE
Schluter Schiene is a finishing and edge-protection profile for the outside corners of tiled surfaces. The vertical walls section of the profile provides a decorative finish and protect adjacent tiles. Other applications include transitions for dado coverings such as carpet, natural stone, or cold-cured resin coatings. SCHIENE features the same design as JOLLY and can be referenced for additional finishes.
SCHIENE in aluminum, anodized aluminum and solid brass features an integrated joint spacer that establishes a defined joint cavity between the tile and the profile.
Available sizes:
3/16", 1/4", 5/16", 3/8", 1/2"
Available finishes:
Stainless steel, solid brass, aluminum, satin and bright brass
|
|
Schluter JOLLY
Schluter Jolly is a finishing and edge-protection profile for the outside corners of tiled surfaces. The vertical wall section of the profile provides decorative finish and protects adjacent tiles. Other applications include transitions for dado coverings such as carpet, natural stone, or cold-cured resin coatings. JOLLY in all finishes features an integrated joint spacer that establishes a defined joint cavity between the tile and the profile.
Available sizes:
5/16", 3/8", 1/2"
Available finishes:
Polished chrome, brushed nickel and brushed antique bronze |
|
Schluter DITRA and Schluter DITRA-XL
Schluter Ditra and Schluter Ditra-XL are polyethylene uncoupling membranes with a grid structure of square cutback cavities and an anchoring fleece laminated to the underside. Ditra and Ditra-XL provide uncoupling through the open rib structure, which allows for in-plane movement that effectively neutralizes the differential movement stresses between the substrate and the tile, thus eliminating the major cause of cracking and delaminating of the tiled surface. In conjunction with tile coverings, Ditra and Ditra-XL form an uncoupling, waterproofing, and vapor management layer, while providing support/load distribution. The combination of these four essential functions allows for the successful installation of tile over a wide range of substrates, including plywood/OSB, concrete, gypsum, heated floors, etc.
Schluter Ditra is 1/8" thick, which minimizes the assembly thickness and reduces transitions to lower surface coverings (e.g., carpet, engineered wood, and vinyl). Ditra allows for ceramic tile application over single-layer plywood or OSB subfloors on joists spaced up to 19.2"o.c. Ditra is listed by cUPC.
Schluter Ditra-XL is 5/16" thick, which permits even transitions between tile and 3/4" thick hardwood flooring. Ditra-XL allows for ceramic tile application over single-layer plywood/OSB subfloors on joists spaced up to 24"o.c.
Available sizes:
Ditra 3' 3" X 98' 5" (smaller roll sizes are available)
Ditra-XL 3' 3" X 53' 3"
|
 |
Schluter KERDI
Schluter Kerdi is a pliable sheet-applied polyethylene waterproofing membrane and vapor retarder that guarantees uniform thickness. It is covered with an anchoring fleece on both sides to anchor the membrane in thin-set mortar and is suitable for waterproofing in conjunction with tiled surfaces on walls and floors. Schluter Kerdi is listed by cUPC and evaluated by ICC-ES.
Available sizes:
3' 3" X 16' 5"
3' 3" X 33'
3' 3" X 98' 5"
|
 |
Schluter KERDI-BAND
Schluter Kerdi-Band is a waterproofing strip used to seal butt joints and floor/wall connections with the Schluter Kerdi and Schluter Ditra membranes, as well as profile connections with the Schluter Bara balcony edging profile series.
Available sizes:
5" X 33'
5" X 98' 5"
10" X 98' 5"
|
 |
Schluter KERDI SHOWER-SC
Schluter Kerdi Shower-SC is a lightweight, expanded polystyrene (PS 40) shower curb specifically designed to integrate with Schluter Kerdi Shower-ST, Kerdi, and Kerdi Drain.
Available size:
48" X 6" X 4-1/2"
|
 |
Schluter KERDI SHOWER KIT
The Schluter Kerdi Shower Kit is an all-inclusive package containing each of the integrated family of components required to create a maintenance-free, watertight shower assembly without a mortar bed.
Available sizes:
48" X 48"
72" X 72"
32" X 60"
Available finishes:
Stainless steel and brushed nickel
|
 |
Schluter KERDI SHOWER-ST
Schluter Kerdi Shower-ST is a sloped shower tray made of lightweight, expanded polystyrene (PS 40) for constructing mortar-free shower receptors. It is specifically designed to integrate with Schluter Kerdi Shower-SC, Kerdi and Kerdi Drain.
Available sizes:
48" X 48" X 1-1/2"
72" X 72" X 1-1/2"
32" X 60" X 1-3/4"
32" X 60" X 1-1/2"
|
 |
Schluter BEKOTEC
Schluter Bekotec is a lightweight modular screed systems that are used to create continuous screed surfaces without control joints or reinforcement and can also accommodate hydronic radiant heating tubes. It produces a permanent flooring assembly that is free from internal stresses by confining the shrinkage and curing stresses which causes deformation such as curling and continuous cracks that is common in a traditional screed. Since it is a floating system, the assembly can be customized to meet a range of heat and sound requirements. For use with ceramic tile, natural stone, or other surface coverings. Schluter BEKOTEC is 1-3/8" thick, and is made of expanded polystyrene.
Available sizes:
24" X 48"
|
 |
Schluter TROBA
Schluter Troba is a reliable and durable subsurface drainage system for use over horizontal waterproofing layers. It consists of a pressure-stable, polyethylene sheet with perforated studs, which enable the water to flow freely to the sloped waterproofing layer and on to the designated drainage exit.
Available size:
3' 3" X 65' 7"
|
Kerdi Board
|
|
|
Schluter-KERDI-BOARD is a multifunctional tile substrate and building panel, which can also be used for creating bonded waterproofing assemblies with tile coverings.
It consists of an extruded polystyrene foam panel, with a special reinforcement material on both sides and fleece webbing for effective anchoring in thin-set mortar.
With the available panel thicknesses of 3/16", 3/8", 1/2", 3/4", 1", 1-1/2", and 2" (5, 9, 12.5, 19, 25, 38, and 50 mm), KERDI-BOARD allows the installer to prepare and create a broad range of substrates and building elements for the installation of ceramic and natural stone tile that are flat, level, plumb, square, and dimensionally stable. With suitable preparation of the abutting seams and joint areas, the panel may be used for bonded waterproofing assemblies.
The boards are simply cut to size with a utility knife. The gridlines, which are printed on the surface, are helpful for neat and quick cuts and installation.
Tiles can be installed directly over KERDI-BOARD using the thin-set method. |
|
Schluter®-SCHIENE
Application and Function
Schluter-SCHIENE is designed to provide edging for tile coverings. Typical applications include edge protection where tile is bordered by carpet, at expansion joints, or as a decorative edging for stairs.
Schluter-SCHIENE is available in stainless steel, solid brass, aluminum, and anodized aluminum. The profile features a trapezoid-perforated anchoring leg, which is secured in the mortar bond coat beneath the tile, and an 87° sloped vertical wall section that transfers point loads to the substrate and surface covering while protecting the tile edges from damage.
Schluter-SCHIENE, in solid brass, aluminum, and anodized aluminum, features a 5° sloped top flange and fillet at the anchoring leg/vertical section interface to enhance edge protection by reducing stresses on the tile, and, in sizes greater than 1/4" (6 mm), features an integrated joint spacer that establishes a defined joint cavity between the tile and the profile. Schluter-SCHIENE, in stainless steel, is roll-formed and does not feature an integrated joint spacer.
The anchoring leg of Schluter-SCHIENE, in all materials, is available with a special radius perforation "R" so that the profile can be used to form curves.
|
 |
Application and Function
Schluter-JOLLY is a finishing and edge-protection profile for the outside corners of tiled surfaces.
It features a trapezoid-perforated anchoring leg that is secured in the mortar bond coat beneath the tile, and an 87° sloped vertical wall section that provides a decorative finish and protects adjacent tiles.
The profile is available in chrome-plated solid brass, color-coated aluminum, anodized aluminum, and PVC. Schluter-SCHIENE features the same design as Schluter-JOLLY and is also available in solid brass, aluminum, and stainless steel. Please see the Schluter-Systems Illustrated Price List for more details.
The range of available sizes and finishes permits the matching of Schluter-JOLLY to a wide variety of tile and grout colors and allows many design opportunities through the use of contrasting colors.
Other applications include transitions for dado coverings such as carpet, natural stone, or cold-cured resin coatings. The integrated joint spacer establishes a defined joint cavity between the tile and the profile.
|
 |
Application and Function
Schluter-RONDEC is a finishing and edge-protection profile for the outside corners of tiled surfaces. It features a trapezoid-perforated anchoring leg that is secured in the mortar bond coat beneath the tile and a reveal that forms a symmetrically rounded outer corner with 1/4" (6 mm) radius along the surface edge.
The profile is available in stainless steel, solid brass, chrome-plated solid brass, color-coated aluminum, anodized aluminum, Tuscan color-coated aluminum and PVC. Schluter-RONDEC's wide range of materials, colors, and surface finishes allows for color coordination with tile and grout and the creation of interesting accents in decorative designs.
In addition to its decorative effect, the profile protects tile edges against damage caused by mechanical stresses. Schluter-RONDEC, in stainless steel, is particularly resistant to wear when used as edge protection. It may also be used as a stair nosing or transition profile.
In addition Schluter-RONDEC is also suitable for transitions, corners, or dado coverings with other covering materials; for example, carpet, parquetry, natural stone tiles, or cold-cured resin coverings. The integrated joint spacer forms a defined joint cavity with the tile.
Note: Schluter-RONDEC, in stainless steel, does not feature the integrated joint spacer. Matching inside and outside corners, including sink corners, and connectors are available.
|
 |
Application and Function
Schluter-REMA is the ideal system for creating concealed access panels in tiled wall coverings.
The Schluter-REMA assembly kit consists of four aluminum brackets with molded casings containing magnets that are clamped to lateral, movable guide shoes, and four ferro-magnetic metal counterplates. Schluter-REMA installation is independent of tile size and thickness and enables exact matching of the access panel to the overall joint design. Thus, panels that access electrical or plumbing components do not impair the visual appearance of the tile covering.
|
 |
Application and Function
Schluter-TREP-SE/-S/-B are designed to protect tiled stair edges and provide an easily visible, slip-resistant wear surface for durable, safe, and visually appealing stair-nosing design. They are suitable for use in areas subjected to heavy foot-traffic, such as offices or public buildings.
The profiles feature a trapezoid-perforated anchoring leg made of stainless steel (TREP-SE) or aluminum (TREP-S and TREP-B), which is secured in the mortar bond coat beneath the tile an supports a slip-resistant thermoplastic rubber wear surface.
The tread surface of Schluter-TREP-SE/-S/-B is available in a variety of colors and can be replaced in case of damage or wear.
The tread surface meets or exceeds the static coefficient of friction recommendation in the Americans with Disabilities Act (ADA), for use in applications where the risk of slipping exists (United States Testing Company, test method ASTM C1028, 0.6 wet, 0.8 dry).
Schluter-TREP-B features a 2-1/8" (52 mm) wide wear surface, easily allowing the designer to produce stairs with the first and the last step marked by a 2" (50 mm) wide strip in a contrasting color to increase visibility and safety.
The leading edges of TREP-SE/-S/-B have a 5/16" (8 mm) radius. Matching end caps are available.
Schluter-TREP-TAP is an anodized aluminum cover profile that integrates with the Schluter-TREP-S/-B stair-nosing profiles to conceal the top of the riser.
|
|
